rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 dc/dc-converter rs1/rd1-s15 1.5w unregulated single output we energize electronics! an acal group company we energize electronics! ? 4 pin sil/ 8pin dil package ? 1000vdc isolaton ? up to 3000vdc isolaton ? low ripple and noise ? efciency up to 88% ? operatng temperature range -40 ~ +85c ? non conductve black plastc case output specification voltage accuracy: 3% line regulaton: 1.2% (per 1%vin change) load regulation: 10% ( from 20 to 100%) load output 3.3v model: 20% ripple noise (20mhz bandwidth): 100mv pk-pk temperature coefcient: 0.02%c capacitor load: see table input specifications voltage range: 10% max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton capacitance: 60pf typ. i/o isolaton resistance: 1000m ohm switching frequency: variable 80khz humidity: 95% rel h reliability calculated mtbf : >1.121mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) pin material sip case: ? 0.5mm alloy42 solder-coated pin material dip case: ? 0.5mm brass solder-coated potng material: epoxy (ul94v-0 rated) weight case- sip: 1.5g weight case-dip: 1.8g dimmension sip: 0.46 x 0.24 x 0.40 dimmension dip: 0.50 x 0.40 x 0.27 absolute maximum ratings (1) input surge voltage (100ms)/ 5 v models: 7vdc max 12v models: 15vdc max 24v models: 28vdc max 48v models: 54vdc max soldering temperature (2) : 260c max. 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) 48=48v 20= 2.0 48=48v rd1 - xx xx x xx power (w) input 03=3.3v t ype a x code inter nal isolation (kvdc) 48=48v 20= 2.0 48=48v dc/dc-converter /d- nrete ne tt we energize electronics! an acal group company we energize electronics! sufx 3 means 3kvdc isolaton mo del selection guide model number in p ut volt age range (vdc) inpu t current output vol tage (vdc) output current efficie ncy capac itor load( uf) no - load (ma ) full lo ad (ma) full l oad (ma) rs1-0 5 03s15ax 5 30 370 3.3 400 81 220 rs1-0 5 05s15ax 5 30 380 5 300 79 220 10 5 07s15ax 5 35 366 7.2 208 82 220 10 5 09s15ax 5 25 400 9 166 75 220 rs1-0 5 12s15ax 5 25 385 12 125 78 220 rs1-0 5 15s15ax 5 30 375 15 100 80 220 rs1-0 5 18s15ax 5 30 353 18 83 85 220 rs1-0 5 24s15ax 5 35 357 24 63 84 220 rs1-1203s15ax 12 15 167 3.3 400 75 220 rs1-1205s15ax 12 25 156 5 300 80 220 rs1-1207s15ax 12 25 167 7.2 208 75 220 11209s15ax 12 20 151 9 166 83 220 11212s15ax 12 15 152 12 125 82 220 11215s15ax 12 15 156 15 100 80 220 11218s15ax 12 15 156 18 83 80 220 rs1-1224s15ax 12 15 164 24 63 76 220 1 240315 24 15 83 3.3 400 75 220 1 240515 24 15 76 5 300 82 220 1 240715 24 10 78 7.2 208 80 220 1 240915 24 10 78 9 167 80 220 1 241215 24 15 74 12 125 84 220 1 241515 24 10 74 15 100 84 220 rs1 - 2418s15 ax 24 10 78 18 83 80 220 1 242415 24 8 71 24 63 88 220 rs1 - 4803s15 ax 48 10 42 3.3 400 75 220 1 480 515 48 10 42 5 300 75 220 1 480715 48 8 41 7.2 208 76 220 1 480915 48 8 41 9 167 76 220 1 481215 48 6 41 12 125 77 220 1 481515 48 6 41 15 100 77 220 rs1 - 4818s15 ax 48 6 41 18 83 77 220 rs1 - 4824s15 ax 48 6 40 24 63 78 220 isolation ?3? means 3 kvdc isolation the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e- mail to : info@rsg - electronic.de
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 dd - - test configurations input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0 at 100khz) at nominal input and full load. lin current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load model number in p ut volt age range (vdc) inpu t current output vol tage (vdc) output current efficie ncy @fl(% ) capac itor load( uf) no - load (ma ) full lo ad (ma) full l oad (ma) rd1 - 0505s15 ax 5 35 390 3.3 400 77 220 rd1 - 0507s15 ax 5 30 385 5 300 78 220 rd1 - 0509s15 ax 5 30 400 7.2 208 75 220 rd1 - 0512s15 ax 5 25 400 9 167 75 220 rd1 - 0515s15 ax 5 25 370 12 125 81 220 rd1 - 0518s15 ax 5 25 366 15 100 82 220 rd1 - 0524s15 ax 5 25 375 18 83 80 220 rd1 - 1203s15 ax 5 30 361 24 63 83 220 rd1 - 1205s15 ax 12 15 170 3.3 400 74 220 rd1 - 1207s15 ax 12 15 154 5 300 81 220 rd1 - 1209s15 ax 12 25 164 7.2 208 76 220 rd1 - 1212s15 ax 12 15 149 9 167 84 220 rd1 - 1215s15 ax 12 15 156 12 125 80 220 rd1 - 1218s15 ax 12 15 156 15 100 80 220 rd1 - 1224s15 ax 12 15 156 18 83 80 220 rd1 - 0505s15 ax 12 15 164 24 63 76 220 rd1 - 1524s15 ax 24 10 83 3.3 400 75 220 rd1 - 2403s15 ax 24 9 76 5 300 82 220 rd1 - 2405s15 ax 24 10 75 7.2 208 83 220 rd1 - 2407s15 ax 24 10 74 9 167 85 220 rd1 - 2409s15 ax 24 10 78 12 125 80 220 rd1 - 2412s15 ax 24 8 76 15 100 82 220 rd1 - 2415s15 ax 24 8 78 18 83 80 220 rd1 - 2418s15 ax 24 9 76 24 63 82 220 3 3 dd - s . - - . note 1.ripple/noise measured with 20mhz bandwidth. 2.tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. dd - - test configurations input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0 at 100khz) at nominal input and full load. lin current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load model number in p ut volt age range (vdc) inpu t current output vol tage (vdc) output current efficie ncy @fl(% ) capac itor load( uf) no - load (ma ) full lo ad (ma) full l oad (ma) rd1 - 0505s15 ax 5 35 390 3.3 400 77 220 rd1 - 0507s15 ax 5 30 385 5 300 78 220 rd1 - 0509s15 ax 5 30 400 7.2 208 75 220 rd1 - 0512s15 ax 5 25 400 9 167 75 220 rd1 - 0515s15 ax 5 25 370 12 125 81 220 rd1 - 0518s15 ax 5 25 366 15 100 82 220 rd1 - 0524s15 ax 5 25 375 18 83 80 220 rd1 - 1203s15 ax 5 30 361 24 63 83 220 rd1 - 1205s15 ax 12 15 170 3.3 400 74 220 rd1 - 1207s15 ax 12 15 154 5 300 81 220 rd1 - 1209s15 ax 12 25 164 7.2 208 76 220 rd1 - 1212s15 ax 12 15 149 9 167 84 220 rd1 - 1215s15 ax 12 15 156 12 125 80 220 rd1 - 1218s15 ax 12 15 156 15 100 80 220 rd1 - 1224s15 ax 12 15 156 18 83 80 220 rd1 - 0505s15 ax 12 15 164 24 63 76 220 rd1 - 1524s15 ax 24 10 83 3.3 400 75 220 rd1 - 2403s15 ax 24 9 76 5 300 82 220 rd1 - 2405s15 ax 24 10 75 7.2 208 83 220 rd1 - 2407s15 ax 24 10 74 9 167 85 220 rd1 - 2409s15 ax 24 10 78 12 125 80 220 rd1 - 2412s15 ax 24 8 76 15 100 82 220 rd1 - 2415s15 ax 24 8 78 18 83 80 220 rd1 - 2418s15 ax 24 9 76 24 63 82 220 3 3 dd - s . - - . note 1.ripple/noise measured with 20mhz bandwidth. 2.tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. dc/dc-converter rs1/rd1-s15 1.5w unregulated single output we energize electronics! an acal group company we energize electronics! sufx 3 means 3kvdc isolaton test configuration note dd - - test configurations input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0 at 100khz) at nominal input and full load. lin current probe cin load output ripple & noise measurement test the scope measurement bandwidth is 20mhz . load model number in p ut volt age range (vdc) inpu t current output vol tage (vdc) output current efficie ncy @fl(% ) capac itor load( uf) no - load (ma ) full lo ad (ma) full l oad (ma) rd1 - 0505s15 ax 5 35 390 3.3 400 77 220 rd1 - 0507s15 ax 5 30 385 5 300 78 220 rd1 - 0509s15 ax 5 30 400 7.2 208 75 220 rd1 - 0512s15 ax 5 25 400 9 167 75 220 rd1 - 0515s15 ax 5 25 370 12 125 81 220 rd1 - 0518s15 ax 5 25 366 15 100 82 220 rd1 - 0524s15 ax 5 25 375 18 83 80 220 rd1 - 1203s15 ax 5 30 361 24 63 83 220 rd1 - 1205s15 ax 12 15 170 3.3 400 74 220 rd1 - 1207s15 ax 12 15 154 5 300 81 220 rd1 - 1209s15 ax 12 25 164 7.2 208 76 220 rd1 - 1212s15 ax 12 15 149 9 167 84 220 rd1 - 1215s15 ax 12 15 156 12 125 80 220 rd1 - 1218s15 ax 12 15 156 15 100 80 220 rd1 - 1224s15 ax 12 15 156 18 83 80 220 rd1 - 0505s15 ax 12 15 164 24 63 76 220 rd1 - 1524s15 ax 24 10 83 3.3 400 75 220 rd1 - 2403s15 ax 24 9 76 5 300 82 220 rd1 - 2405s15 ax 24 10 75 7.2 208 83 220 rd1 - 2407s15 ax 24 10 74 9 167 85 220 rd1 - 2409s15 ax 24 10 78 12 125 80 220 rd1 - 2412s15 ax 24 8 76 15 100 82 220 rd1 - 2415s15 ax 24 8 78 18 83 80 220 rd1 - 2418s15 ax 24 9 76 24 63 82 220 3 3 dd - s . - - . note 1.ripple/noise measured with 20mhz bandwidth. 2.tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5. operation under no - load conditions will not damage these devices, however they may not meet all listed specifications.
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 pin connections pin number 1 2 4 3 single v input +v input +v output v output pin connections pin number 1 4 7 5 single v input +v input +v output v output the pin connection of high isolation one is the same with normal one. 11. 6 8 ( 0 . 46) 9 . 6 5 ( 0 . 38) 0 . 5 0 (0. 02) 3 . 0 0 ( 0 . 12) 2 . 5 4 ( 0 . 10) 1 . 6 0 (0. 06) 0 . 2 5 ( 0 . 01) 0 . 5 0 (0. 02) 0 . 5 0 (0. 02) 6 . 00* ( 0 . 24) printed face 1 3 4 2 dc-dc conver ter x x x x 6 . 8 5 ( 0 . 27) 1 2 . 7 0 ( 0 . 50) 10. 1 6 ( 0 . 40) 7 . 6 2 ( 0 . 3 0 ) 7 . 6 2 ( 0 . 30) 0 . 5 0 ( 0 . 02) 2 . 5 4 ( 0 . 10) 0 . 5 0 ( 0 . 02) bottom view 3 . 0 0 ( 0 . 12) dia 0 . 5 0 ( 0 . 02) 1 4 5 7 dc-dc conver ter x x x x notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) 8 pin dil package * the thickness of 48v input voltage model i s 7.50(0.29) 4 pin sil package notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) the pin connection of high isolation one is the same with normal one. rs1-xxxxs15a1 rd1-xxxxs15a1 pin connections pin number 1 2 4 3 single v input +v input +v output v output pin connections pin number 1 4 7 5 single v input +v input +v output v output the pin connection of high isolation one is the same with normal one. 11. 6 8 ( 0 . 46) 9 . 6 5 ( 0 . 38) 0 . 5 0 (0. 02) 3 . 0 0 ( 0 . 12) 2 . 5 4 ( 0 . 10) 1 . 6 0 (0. 06) 0 . 2 5 ( 0 . 01) 0 . 5 0 (0. 02) 0 . 5 0 (0. 02) 6 . 00* ( 0 . 24) printed face 1 3 4 2 dc-dc conver ter x x x x 6 . 8 5 ( 0 . 27) 1 2 . 7 0 ( 0 . 50) 10. 1 6 ( 0 . 40) 7 . 6 2 ( 0 . 3 0 ) 7 . 6 2 ( 0 . 30) 0 . 5 0 ( 0 . 02) 2 . 5 4 ( 0 . 10) 0 . 5 0 ( 0 . 02) bottom view 3 . 0 0 ( 0 . 12) dia 0 . 5 0 ( 0 . 02) 1 4 5 7 dc-dc conver ter x x x x notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) 8 pin dil package * the thickness of 48v input voltage model i s 7.50(0.29) 4 pin sil package notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) the pin connection of high isolation one is the same with normal one. rs1-xxxxs15a1 rd1-xxxxs15a1 pin connections pin number 1 2 4 3 single v input +v input +v output v output pin connections pin number 1 4 7 5 single v input +v input +v output v output the pin connection of high isolation one is the same with normal one. 11. 6 8 ( 0 . 46) 9 . 6 5 ( 0 . 38) 0 . 5 0 (0. 02) 3 . 0 0 ( 0 . 12) 2 . 5 4 ( 0 . 10) 1 . 6 0 (0. 06) 0 . 2 5 ( 0 . 01) 0 . 5 0 (0. 02) 0 . 5 0 (0. 02) 6 . 00* ( 0 . 24) printed face 1 3 4 2 dc-dc conver ter x x x x 6 . 8 5 ( 0 . 27) 1 2 . 7 0 ( 0 . 50) 10. 1 6 ( 0 . 40) 7 . 6 2 ( 0 . 3 0 ) 7 . 6 2 ( 0 . 30) 0 . 5 0 ( 0 . 02) 2 . 5 4 ( 0 . 10) 0 . 5 0 ( 0 . 02) bottom view 3 . 0 0 ( 0 . 12) dia 0 . 5 0 ( 0 . 02) 1 4 5 7 dc-dc conver ter x x x x notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) 8 pin dil package * the thickness of 48v input voltage model i s 7.50(0.29) 4 pin sil package notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) the pin connection of high isolation one is the same with normal one. rs1-xxxxs15a1 rd1-xxxxs15a1 dc/dc-converter rs1/rd1-s15 1.5w unregulated single output we energie electronics an acal group copan we energie electronics 8 pin dil 4 pin sil the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
